HCP Submersible Sewage Pump :F21PF-3 3 phase With auto float switch Features A precision manufactured motor is achieved by utilising the highest standard of quality control. All rotors adopt heat treatment methods for drive shaft assembling. Stator winding impregnated with varnish that is heat dried in an industrial oven. Standard accessories include : cable with an epoxy resin sealed water resistant cable base, Auto-cut thermal motor protector, dual mechanical seals and lip seal design. Applications Drainage of sewage from the building basements, hotel industry, and waste water from factories Drainage of sewage from industrial process factories Emptying of septic tanks, cesspits and sewage pump stations. Pumping surface and drainage water from garages and sprinkler systems. Specifications Power 1 HP (750 watts) Discharge 2″ (50mm) Phase 3Ø Start Method Direct Efficient / Maximum Head 9 / 13 meters Efficient / Maximum Flow Rate 200 / 350 L/min Solid Passage 26mm Weight 18 kg read more

PEDROLLO CP158 (ITALY) 0.75kW, 90L/min, 34mH, 3phase, 1″x1″ Specifications Size Discharge 1″ x 1″ Power 750 W / 3 phase Flow Rate 10 ~ 90 L/min Head 34 ~ 25 meters Manometric Suction Lift Max. 7 meters Liquid Temperature Max. +90°C Environment Temperature Max. +40°C Dimensions (L x W x H) 286mm x 190mm x 240mm Weight 12 kg Applications water supply systems air conditioning systems pressure systems cooling systems irrigation pumps liquids transfer read more

HCP Submersible Dewatering Pump :IC215 HCP IC215 (made in Taiwan) is submersible dewatering pump for agriculture water supply. 1 phase Features The internal casting is treated with high solid painting, which can double the duration of anti-rusting, and extend the lifetime of the product. Standard design, incorporating a dry motor with thermal auto-cut that prevents the motor from over heating, and a cast iron motor frame for a faster heat dissipation. As well as an abrasion resistant double mechanical seal and an additional oil seal. Water cooled motor to ensure a long life in continuous and intermittent operation, with high efficiency and energy savings. An exceptional High-lift and suction impeller design, which allow for dewatering of underground or circulating water applications. For above or below surface water applications; the IC pump strainer can be easily removed and replaced with a check valve, which allows for dewatering up to max. 8m deep of underground water and water circulation applications. (W–Well Type) New casing cover, with metric thread bolt hole that is easier for valve and adapter connection. High solids Epoxy coating prolong metals from corrosion and oxidisation. Applications Agriculture water supply and drainage. Water supply for agricultural irrigation systems and underground water pumping. Landscape, water feature and horticulture irrigation. Extraction of water from rivers, lakes and reservoirs. Limits of use Liquid temperature: 0~40°C (32~104) Submersion Depth: 30m (100 ft) Specifications Power 1.5 HP (1100 watts) Discharge 2″ (50mm) Phase 1Ø Start Method Capacitor Efficient / Maximum Head 13.5 / 18 meters Efficient / Maximum Flow Rate 200 / 380 L/min Solid Passage 3.5mm (1/4″) Weight 28 kg read more

Two impeller centrifugal pumps MODEL : CBT600  CBT 600 for constructing pressurisation systems form civil and industrial plant, the two counter-posed impellers guarantee high head with good delivery.   Pump Tecnical specifications POWER:     4kw , 5.5hp ELECTRICITY:Three phase (3)  MANOMETRIC HEAD (max): 80,4 (m) PERFORMANCE: 225 (Lt/min) NOZZLE: 11/2'' x 11/4'' (inch) read more

HERO TECH INVERTER STICK WELDING MACHINE MODEL:GM1800 MMA SERIES (MOSFET) Features: Good performance with automatic compensation for voltage fluctuation Small and light weight, portable and durable, reliable and economical Stable arc, deep molten, perfect welding shaping Low consumption with low open energy wastage Suitable for welding stainless steel, carbon steel and other metal SPECIFICATION GM - 1800 GM - 2000 GM - 2200 Input Voltage (VAC) 220, 1 50 / 60Hz 220, 1 50 / 60Hz 220, 1 50 / 60Hz Rated Voltage (%) 15 % 15 % 15 % Rated Input Current (AAC) 12.3 24 28.2 Rated Input Power (KVA / KW) 4.4 / 3.8 5.3 / 4.9 6.2 / 5.9 Output Current (ADC) 20 - 140 20 - 160 20 - 200 Rated Duty Cycle (%) 60 100 60 Open Circuit Voltage (VDC) 70 60 70 Output Voltage (VDC) 25.6 26.4 27.2 Efficiency --- 85 % 85 % 85 % Power Factor 0.93 0.93 0.93 Insulation Class (LEVEL) F B B IP Rating (LEVEL) IP23 IP21 IP21S Dimension (W*D*H) 130*300*240 175*380*300 180*390*300 Weight (KG) 5.0 7.0 7.5 read more

High pressure air compressor with Yanmar Diesel Engine L100N6, key start. Model: HVU-205E (Yanmar L100N6 Diesel Engine) Key start & Coil start. High pressure compressed air comes from two stage compressing air compressor, to disassemble the tire fast and easily. Adjustable torque air wrench-ensure the stud firmly lock. With petrol engine driving:Provide efficient power to the required work at anywhere. Extremely convenient to on call service. Control System  Automatic UnloaderSystem “U” Type The automatic unloading system allows for the control of loaded and unloaded compressor states through a range of pre-set pressure values. This system is recommended where the duty cycle exceeds 50% and for all larger compressors units. Specifications Yanmar L100N6 Diesel Engine 10 hp Working Pressure (kg/cm²) 12 Bar Compressor Speed 900 rpm F.A.D 406 L/min Tank Capacity 237 Liter Compressor Block Physical Dimension (L x W x H) 560mm x 380mm x 460mm Weight 67kg Compressor Unit Physical Dimension (L x W x H) 1470mm x 550mm x 1100mm Weight 240kg read more

Submersible Wastewater Pump MODEL:A-21 HCP A-21 (made in Taiwan) is a submersible pump for general waste water. 1 phase Without auto float switch Features   A precision manufactured motor is achieved by utilising the highest standard of quality control. All rotors adopt heat treatment methods for drive shaft assembling. Stator winding impregnated with varnish that is heat dried in an industrial oven. HCP’s professional assembly line, complimented with a synthesised production test, ensures the highest level of final pump quality. Standard accessories include : cable with an epoxy resin sealed water resistant cable base, Auto-cut thermal motor protector, dual mechanical seals and lip seal design. Applications   Waste water Sump drainage Flood control Dewatering for fish pond or basement and cellars Specifications   Power 1 HP (750 watts) Discharge 2″ (50mm) Phase 1Ø Start Method Capacitor Efficient / Max Head 10/13 meters Efficient / Maximum Flow Rate 180/360 L/min Solid Passage 10mm Weight 17 kg   read more

TEC Vibrator motor (TMV0500/15) 0.37kW-4P, 5KN, 415V/3ph/50Hz Three phase Foot Mounting Industrial Vibration Motor (MV Standard Series) Technical Features Quality - World class materials, durable sealing, Premium bearings, strong body design (FEM designed), Vacumn insulation, 3D quality check. Efficiency - Optimised power, Weight ratio, SI continous duty service, Optimized electric design. Reliability - PTC thermistor 180 degrees, Specific grease retaining device, Tropicafised standard, IP66 protection, Class F insulation. Flexibility - Easy mass adjustment, Various voltages and frequencies available, Easy access to the terminal box, Multiple eye-bolts. Product Application & Cases It is widely used in vibrator feeder, construction materials, sand/cement screening, material milling, flow conveyor, vibration separator, hoppyer emptying, bin activator, etc. Specification: TMV0500/15 Voltage (V): 415 Current A.max(Y): 1.06 Input Power (KW): 0.37 Force (KN): 5 Weight (KG): 21 Size: size40 read more

TRANSMAX G3 HELIGAL GEAR MOTOR:G3-FM-22-060-020 MOTOR:0.2KW X 415V RATIO:1/60 Transmax G3 Helical Gear Reducer General Specifications • Two types of housings: Aluminium alloy and casgt iron; Two kinds of framws: foot mounting and flange mounting. They are good-looking in appearance, suitable universal mount. • Helical gear with the high-tensile alloy material makes the construction more compact, housing smaller, efficiency higher, output torque larger. • Hardened facing transmission gear that fine finished has the advantages below: seldom distortion high precision, stable running, low noise, it also can work continually under the dreadful conditions. • With 6 specification for the diameter of output shaft: Ø18, Ø22, Ø28, Ø32, Ø40, Ø50. • Two or three-stage transmission, large in ratio range, each single frame size with 14 ratios from 5:1 to 200:1. • Using high quality bearing prolongs the use life. • High-performance oil seal prevents the lubricant from leaking back to the inner of motor. • Three-phase motor combined the standard and full-enclosed aluminium motor, which is good waterproof, easy in heat dissipation, high in running efficiency. • Modular combination extends the transmission ratio from i=5:1 to 1400:1. read more